Lamp and Fuse Tester Circuit Diagram

Lamp and Fuse Tester Circuit Diagram

WEARIFY   April 03, 2018   1 comment:

Why a lamp tester or fuse tester? Testing cables, wires, lamps… belongs to a repair job and sometimes this becomes too cumbersome since one has only two hands and too often, one has to hold the part being tester and the two probes of an ordinary continuity tester all at the same time.

This fuse and lamp tester enables easy testing of lamps and fuses by using the conductivity of the human body. One of the test probes is connected to the part under test while the other probe is hel dby the normal hand.

Lamp and Fuse Tester Circuit Diagram 

When the lamp or fuse is working properly, your eyes will glow in the dark! Just kidding :) . When the lamp or fuse is working properly, a small amount of current flows through the hand which is enough to switch the transistors and light the LED.

Read More

Reliable Car Battery Tester Circuit Diagram

Reliable Car Battery Tester Circuit Diagram

WEARIFY   April 03, 2018   No comments:

This circuit uses the popular and easy to find LM3914 IC. This IC is very simple to drive, needs no voltage regulators (it has a built in voltage regulator) and can be powered from almost every source. This circuit is very easy to explain: When the test button is pressed, the Car battery voltage is feed into a high impedance voltage divider. His purpose is to divide 12V to 1,25V (or lower values to lower values).

This solution is better than letting the internal voltage regulator set the 12V sample voltage to be feed into the internal voltage divider simply because it cannot regulate 12V when the voltage drops lower (linear regulators only step down). Simply wiring with no adjust, the regulator provides stable 1,25V which is fed into the precision internal resistor cascade to generate sample voltages for the internal comparators. Anyway the default setting let you to measure voltages between 8 and 12V but you can measure even from 0V to 12V setting the offset trimmer to 0 (but i think that under 9 volt your car would not start).

There is a smoothing capacitor (4700uF 16V) it is used to adsorb EMF noise produced from the ignition coil if you are measuring the battery during the engine working. Diesel engines would not need it, but I'm not sure. If you like more a point graph rather than a bar graph simply disconnect pin 9 on the IC (MODE) from power. The calculations are simple (default)

For the first comparator the voltage is : 0,833 V corresponding to 8 V
* * * * * voltage is : 0,875 V corresponding to 8,4 V
for the last comparator the voltage is : 1,25 V corresponding to 12 V
Have fun, learn and don't let you car battery discharge... ;-)

Read More

MT8870 DTMF Telephone Dial Tone Decoder Circuit Diagram

MT8870 DTMF Telephone Dial Tone Decoder Circuit Diagram

WEARIFY   April 03, 2018   No comments:

Build a MT8870 DTMF Telephone Dial Tone Decoder Circuit Diagram. This is a  simple MT8870 DTMF Telephone Dial Tone Decoder Circuit Diagram. In this circuit one common DTMF receiver IC is the Motorola MT8870 that is widely used in electronic communications circuits. The MT8870 isan 18-pin IC. It is used in telephones and a variety of other applications. When a proper output is not obtained in projects using this IC, engineers or technicians need to test this IC separately. 

A quick testing of this IC could save a lot of time in research labs and manufacturing industries of communication instruments. Here’s a small and handy tester circuit for the DTMF IC. It can be assembled on a multipurpose PCB with an 18-pin IC base. One can also test the IC on a simple breadboard. For optimum working of telephone equipment, the DTMF receiver must be designed to recognize a valid tone pair greater than 40 ms in duration and to accept successive digit tone-pairs that are greater than 40 ms apart. 

 MT8870 DTMF Telephone Dial Tone Decoder Circuit Diagram

Read More

Telephone for VoIP gate Circuit Diagram

Telephone for VoIP gate Circuit Diagram

WEARIFY   April 02, 2018   No comments:

A project of Telephone for VoIP gate Circuit Diagram. Calls over the Internet can be in several different ways. For households with a permanent connection to the Internet, it is advantageous to use different IP phones and VoIP gateways that need to function on the computer. Because IP phones are still relatively expensive, they are used more often different VoIP gateway. VoIPgateway is "one end" connected to a network with access to the internet, the "other end" connects a standard analog phone, which is then used in the normal way and that has given a telephone number available from any fixed or mobile phone. Some VoIP gateway router in addition to that we need as well, if we want to access via a modem to connect multiple computers. To my VoIP gateway, we can connect nehomologovaný, self made ​​phone. Instructions for simple phone is the subject of this article.

How to the phone works

Normally the phone line is a DC voltage, usually 50 to 70 V. During the ringtone to this voltage superposed yet AC 50-100 V with a frequency of usually 20 or 25 Hz. "Pick up the 'phone line will pass through the current 20-40 mA. On the phone while the voltage drop occurs several volts (Fig. 1). This voltage can be used to power the circuitry phone. The polarity of the DC voltage is not defined, the phone must function in both polarities. The phone line is when answering the call of a defined impedance, which should be adapted telephone. Line impedance in different countries vary so as the phone purchased in Germany (impedance 220 ​​ohms + 820 ohms in parallel with 220 nF) not in Bohemia (600 ohms) to work optimally. Sometimes differ impedance different networks within the same country, depending on the age and type of telephone exchanges, length and characteristics of the cables.

Fig. 1 The voltage on the raised phone would, depending on the passing stream should be in the area indicated by the letters A to G

The most important part of the phone is a colloquial circuit. The call is transmitted over the line modulation current that flows through the line. The current is modulated on the side panel (VoIPGateway), which transfers the call to the user, and in the device, which is transmitted from the user. The speech circuit is a hybrid circuit that suppresses the signal from the microphone in the earpiece. The hybrid circuit is on the opposite side (PBX, VoIP gateway). The hybrid circuit is usually some sort of bridge, and therefore it is necessary to impedance phone and VoIP gateway (or exchange) have been adapted. It is important especially for VoIP devices, where the influence of digitization and transmission of data over the Internet arises signal delay in the order of tens of milliseconds. Mismatch, especially on the VoIP gateway, there is a very annoying echo.

Fig. 2 Colloquial hybrid transformer circuit. If L1 and L2 have the same number of threads and balancing impedance ZM is equal to the line impedance ZL, the microphone signal in the handset suppressed


Another important part of the circuit for dialing. All modern devices support tone dialing. Ringing circuit to alert the user to an incoming call. Acoustic (bell) or optical signals indicates the presence of ringing voltage on the line. Hook switch is a switch that turns on the circuit colloquial answer the phone.

Specifications

Telephone impedance:	aprox. 600 Ohm.
Recomended line impedance:	real. 600 Ohm.
Operating (off-hook) current:	20 mA (10 to 40 mA.)
Operating voltage:	aprox. 7 V @ 20 mA.
Dialing:	DTMF
"In-use" indication:	3 to 15 V/ aprox. 1 mA
On-hook current:	aprox. 0,01 mA @ 50 V

Phone Circuit Schematic

Fig 3rd Telephone unit schematic

Connection phone in Figure 3 Colloquial circuit with transistors T1 to T3 is connected via a hook switch and bridge DB1 to the telephone line . Diode bridge ensures that electronic circuits are supplied with the correct polarity. If the hook switch is closed, current passes through the transistor T1 lines , which is used as microphone amplifier and transistors T2 and T3 , which amplifies the signal to the receiver. Headphone amplifier operates in class A. The amplitude of the output voltage at the collector of the transistor is about 1 V, which for the purpose of completely sufficient . Headphones or speakers can be used with an impedance of 8 ohms , the amplifier but works better (has lower distortion) with higher impedance load . Trimmer P2 can adjust the gain as needed.

The amplifier is continuously drop of about 1.3 V, the sum of the voltage UBE transistors T2 and T3 and is only slightly dependent on the flowing current. This voltage across the resistor R1 is powered electret microphone . The signal from the microphone passes through C1 to the base of transistor T1 . It amplifies the signal level required to excite the line. Originally, the microphone amplifier much more difficult . But he had unnecessarily high gain and output impedance inappropriate . This simple connection works better . Working point T1 is set resistors R2 to R4 . The microphone amplifier there is a voltage drop of about 3.5 V , the voltage drop can be under current amplification T1 changed 3 to 4 V. Resistor R5 introduced at this stage, a negative feedback regulating the amplification and decreasing distortion. Balancing circuit C6, R6 and P1 suppresses the signal from the microphone in headphone amplifier .

The signal from the microphone is on the collector of T1 opposite phase than the emitter , but the amplitude of the signal at the collector is much greater. Potentiometer P1 can set a condition where the signals from the collector and emitter of the capacitor C7 T1 readings and audio from the microphone in the handset is suppressed. Simplified diagram balancing the bridge is in Figure 4 The setting is very dependent on the impedance of the line. Because VoIP gateway creates a link with the active resistance of 600 ohm and short supply does not create a significant reactive component , the setting is simple and very effective. The signal coming from the gateway or PBX is the collector and emitter of T1 phase balancing circuit and is therefore not suppressed.

Fig. 4th Simplified wiring hybrid (balancing) circuit in the phone

In order to suppress its signal worked well on the VoIP gateway, you need the phone to be defined impedance close to the impedance of the gate, ie 600 ohm. The output impedance of the collector T1 for AC signals, large, almost current source. Impedance of the phone for voice signals are essentially a parallel combination of R6, R1 and about one order larger impedance collector T1. Rectifier bridge through which the signal passes, it will affect the impedance to a minimum.

 Fig 5 Dialer circuit arrangement

For DTMF I did not find any suitable integrated circuit , and generate DTMF signal discrete oscillators would be difficult and impractical . Finally, I modified the DTMF phone dialer . Dialer is a small box with buttons and speaker , generating tones when you press the button corresponding to the relevant figures. It is used for remote telephone answering and for the selective choice of the civil radio stations . The dialer (Fig. 5 ), the signal goes from the integrated circuit via the 22k resistor on the transistor, which drives a small speaker . Transistor speaker and I vymontoval a DTMF signal is connected to the transistor T4 on the phone. After pressing the button, the IO output voltage appears about 1 V with superimposed DTMF signal . Connect the telephone line is very simple, just enough transistor T4 and resistor R7. The change in resistance R7 can adjust the intensity of tone . Speaker of the phone dialer I used it as a handset . Dialer , according to the type of memory to 11 or 13 numbers , but unfortunately it lacks useful the " Redial" to repeat the last number called. I could not deal with power dialer from the phone line , so your phone is a small battery , which is likely to last for many years. The battery has an advantage in that it forgets the stored phone numbers if you disconnect it from the line.

Also, the ringing circuit I did not get special IO . That's why I like bell oscillator is used samovybuzujícím a piezoelectric transducer . The oscillator is fed stream that passes through the ringer capacitor C8 , bridges DB2 , LED2 to LED4 and resistor R14 . The oscillator is operated only in one half , the sound is more significant . In the other half cycle current through diode D1 . The bell must have a dead zone . That there is provided connecting the LED. Ringing voltage amplitude must have at least 10 V to Buzzer began publishing a sound. The phone I used a blue LED with high luminance. These intensely lit even at current several milliamps , which is ringing flow. LED also serves as a visual alarm bell , which could be useful in noisy environments .

The last telephone circuits are busy lamp . Phone I was seeking a second phone in parallel connected to the device at the other end of the apartment . When the phone is " suspended " , the hook switch is switched to the circuit with transistors T5 and T7 . If all telephones on the line hung on the line voltage of 50 to 60 V. The transistor T5 is opened, closed, and T7 LED1 off. The circuit is taken from the line is very little current through resistors R8 and R9 . Shrinks if the line voltage is below 15 V, T5 is closed , opens T7 and LED1 lights up. Transistor T6 T7 gate bias control by the loss of the R11 so that LED1 is energized about 1 mA , which is quite sufficient for display . In the voltage range of 3-15 V line lights LED1 virtually the same. BSS123 transistor has a maximum voltage UDS only 100 V. If the ringtone is this voltage is exceeded. In my phone's built higher voltage transistor has lasted several months . If you're worried about him , you can type BS108 with UDSmax 200 V, but it is not in SMD . The "in use" circuit not be planted, if you indicate you do not need , or can be used alone for another phone .

Mechanical Design

Width of the printed circuit board was designed dimensions dialer , then the length of a "reasonable " distance between the microphone and earpiece. Although the board is a lot of space , most of SMD components . They take up less space and is easier mounting plate is not so much tinkering . Figure motive circuit and layout of components , following table .

Before you assemble components, prepare the first dialer and attach it to desce.Z dialer remove the battery and remove the hinged cover. Dialer carefully "crack". It should go fairly easily if you start in the corner, to which is attached a chain. Odpájíme the speaker wires from the board dialer and speaker carefully shucks from the bottom of the box. The board dialer vypájíme more transistor in TO92. The board dialer solder short wires to negative (Pad1) and positive (PAD3) terminal electrolytic capacitor and terminal for transistor-based vypájeného (PAD2). Editing is perhaps evident from Figure 9 photos The lower part of the housing dialer yet only tentatively secured to the plate phone plastic rivets (Fig. 10). We remove the box and the board will be filled by phone components.

 Fig. 6th Editing dialer and connection terminals

Phone was originally in a transparent plastic box, which was inside the LED backlight. Its production, however, I not successful, so I made ​​a wooden box. To her I used plywood manufacture of soft wood, obtained from the fruit of hazel. That will free devoted almost everyone greengrocer. From one high hazels get material for a few boxes. Plywood is easily machined and well bonded dispersion adhesive. I eventually recut the box, namořil and přelakoval polyurethane varnish.

 Fig. 7th Mounting boxes dialer

With the change in boxes I had to adjust some components on the board. LEDs were originally all SMD. Finally, there were only SMD LED 2. But it is not visible from the outside, and therefore does not need much light. You can replace the zener diode (3-12 V) or short-circuit, but it increases the sensitivity of the ringing circuit. Other LED in case of 3 mm diameter. It turns out that it is better to use LED with high luminous than type 2 mA of current, because the small stream shines more. Also switch SW1 on the phone "lifting", I moved to the side boards. Deferred phone is on the table laid down the keyboard. LED on the back because they are easy to see and switch is when you pick up the phone available with one touch. Of the joints it can not be soldered to the board just because they do not get tipped soldering iron to solder pad. On the solder contacts because I rozklepl small rivets, which I soldered joints by.

I then links to the rivets inserted the switch and soldered it from the opposite side of the board. Between the switch and the plate I put a piece of insulating paper. The switch can also be placed at any other suitable location in the box and board interconnect wires. Switches P-B143 of the newer series ("silver") are not too good and We turn the lever sometimes lose contact. To fix it so that "packs" pertinax holding plate with pins a little more same hopper. The defect had all the pieces that I had at home. Dimensionally the same switch, but painted black were fine.

 Fig. 8th The top side of the printed circuit board

The power dialer instead of the original articles I used lithium batteries. Do you solder boards phone as housing purchased as the GM and housing that vypájíte of defective motherboards PC that has otherwise placed pins. Piezoelectric transducer is bolted small screws through the PCB to the bottom of the box dialer.
On the microphone I slid the piece of tubing so that the tubing fit snugly inside the box. Thus reducing the acoustic coupling between the earpiece and microphone inside the device.

 Fig. 9th The underside of the plate and box

Fig. 10th The back of the phone with LED switch and a hole for the bell

Animation

Phone use in conjunction with the gateway Linksys Sipura SP2100. In the firewall settings to make sure that in menu / admin / voice / advanced tab you have set up Regional impedance lines FXS Port Impedance: 600 Phone can revive a product as shown in Figure 14 (SW1 closed). You can test with a different phone when line current, measure the voltage on the line and estimate the impedance of the phone - AC voltage test point should be after the switch opens twice. The trimmer P2 dial to maximum resistance (max volume). To attach the microphone sound source (eg mp3 player headphones) and adjust the trimmer P1 so that the sound from the microphone not hear the telephone handset. Try tone. Ringing circuit you can try connecting the phone via a suspended resistor 1 kOhm to AC voltage 24-50 V.

 Fig. 11th test preparation

Conclusion

The phone is in operation for several months and yet it was conceived as a second auxiliary telephone is often used. I have tested it successfully on the public switched telephone network (PSTN), but because I'm not sure whether it meets all required standards, there should not be connected. PSTN to VoIP gateway over a larger voltage when hanging up a more current when the phone is picked up.

List of components
 

R1	4,7 kOhm, SMD 1206
R2	1 kOhm, SMD 1206
R3, R4	22 kOhm, SMD 1206
R5	33 Ohm, SMD 1206
R6	2,2 kOhm, SMD 1206
R7	220 Ohm, SMD 1206
R8, R9	10 MOhm, SMD 1206
R10	330 kOhm, SMD 1206
R11	470 Ohm, SMD 1206
R12	220 kOhm, SMD 1206
R13, R14	10 kOhm, SMD 1206
P1	250 Ohm, trimr PT6V (Piher)
P2	5 kOhm, trimr PT6V (Piher)
C1	220 nF, SMD 1206
C2	10 mikroF/16 V, tantalum., SMD B
C3	1000 mikroF/6,3 V, electrolytic
C4, C5	100 mikroF/6,3 V, tantalum, SMD D
C6	47 mikroF/16 V, tantalum., SMD D
C7	4,7 mikroF/10 V, tantalum, SMD A
C8	220 nF/250 V, foil MKT RM5
	PCB board bcs59

D1	1N4148SMD, SOD80
DB1, DB2	S250,mini DIP bridge
ZD1	BZV55C15SMD, Zener. diode 15 V SOD80
T1, T3	BC817-40, SOT-23
T2	BC807-40, SOT-23
T4 až T6, T8	BC848C, SOT-23
T7	BSS123, SOT-23 (BS108, TO92)
LED1	high intensity 3 mm red LED (it's better than 2 mA LED)
LED2	any 3 mm SMD LED or Zener diode 3 to 12 V
LED3, LED4	high intensity 3 mm blue LED (it's better than 2 mA LED)
MIC1	elektret. mikrofon MCE100
SP1	tiny speaker or headphone 100 Ohm (8 to 100 Ohm), removed from dialer
B1	CR2032 battery and holder
SW1	P-B143, SPST switch
K1	slim RJ11 plug WEBP 6-4 LP
SP2	piezo KPT2038FW
dialer	dialer DTMF 13 or 11

Read More

Telephone Record Control Circuit Diagram

Telephone Record Control Circuit Diagram

WEARIFY   April 02, 2018   No comments:

This circuit will allow you to connect any tape recorder that has a mic and remote input to a phone line and automatically record both sides of a conversation when ever the phone is in use. You will need to take a couple of voltage readings before connecting the circuit. First determine the polarity of your phone line and connect it to the circuit as shown and then determine the polarity of the remote input and connect it to the circuit. Circuit operation is as follows. When the phone is on hook the voltage across the phone line is about 48volts dc. When the phone is off hook the voltage will drop to below 10volts dc. When the line voltage is at 48volts the FET is off which causes Q2 and Q3 to be off. When the phone is picked up the FET turns on along with Q2 and Q3 which turns your recorder on. The tape recorder must be in the record mode at all times. As you can see the power source for the circuit is the phone line.

Circuit Diagram

Read More

Telephone Tapping Indicator Circuit Diagram

Telephone Tapping Indicator Circuit Diagram

WEARIFY   April 02, 2018   No comments:

This simple circuit can indicate a misuse or tapping of Telephone line through a loud alarm. The circuit is too simple and can be easily assembled on a common PCB. Line voltage of Telephone lines is around 48 volts DC in the On hook state. When the handset is lifted, this voltage reduces to 12 volt DC. This change in voltage level is used to activate the circuit.When the switch S1 is closed, circuit becomes active and the telephone enters into the armed state.

The high volt DC from the telephone line passes through R1 and VR1 and bias T1 into conduction. As a result, the collector of T1 goes to ground potential to inhibit T2 from conduction. Buzzer and LED thus remain off. When the handset is lifted, the DC voltage from the telephone lines drops to 12 volts. This turns off T1 and T2 conducts. Buzzer beeps and LED lights indicating that the telephone is using.

Telephone Tapping Indicator Circuit Diagram

Setting
Connect the circuit to Telephone lines using a telephone plug. The free socket of the telephone or Caller ID can be used. Close S1 and adjust VR1 till buzzer stops beeping. Lift the handset. Buzzer should sound. Otherwise, just adjust VR1 till buzzer beeps.

Read More

Simple Car Alarm Arming Horn Beep Canceller Project

Simple Car Alarm Arming Horn Beep Canceller Project

WEARIFY   March 31, 2018   No comments:

This is the Simple Car Alarm Arming Horn Beep Canceller Circuit Diagram Project. It's a great convenience that most modern cars come with a built in alarm, however it is nothing but noise pollution that the horn sounds when the alarm is armed. Disconnecting the alarm system from the horn relay will eliminate this, but prevent the horn from sounding in the even of an actual alarm. This circuit serves to silence the arming beep yet maintain the alarm by introducing a small delay into the signal. 

 

Car Alarm Arming Horn Beep Canceller Circuit Diagram

 

It sits between the alarm and horn relay. The alarm must provide a constant horn signal for at least 3 seconds before the horn relay is activated. That way the quick "beep" will never activate the horn relay, while the constant alarm signal will. 

Part           Total Qty.             Description

C1                   1           0.01uF Ceramic Disc Capacitor   

C2                   1           100uF 35V Electrolytic Capacitor   

R1                   1           1K 1/4W Resistor   

R2                   1           10K 1/4W Resistor   

R3                   1           15K 1/4W Resistor   

R4                   1           470 Ohm 1/4W Resistor   

D1, D3, D4      3           1N4004 Rectifier Diode   

D2                   1           Red LED   

U1                   1           555 Timer IC   

K1                   1           SPST 12V Automotive Relay   

MISC               1          Board, Wire, Socket For U1, Case   

Read More

Simple Over Voltage Protector Circuit Diagram

Simple Over Voltage Protector Circuit Diagram

WEARIFY   March 31, 2018   No comments:

This is the Simple Over Voltage Protector Circuit Diagram. The whole circuit of over voltage protector is build and fabricated around operational amplifier used as comparator. The inverting input is given to pin 2 of op-amp IC (IC1) with reference voltage of 5.1V from zener diode. Similarly, non-inverting input is given to pin no 3 of IC1 use as sensor for over voltage protector for sensing voltage fluctuation in the mains. The two transistors T1 and T2 conduct alternating (i.e. one at a time) according to the voltage of mains.

Simple Over Voltage Protector Circuit Diagram

When voltage is around or below 240V AC transistor T1 is in off-state where T2 energized relay RL1. Similarly, when voltage becomes beyond 240V (i.e. above 240V) T1 is in conducting-stage and T2 is in off-stage which de-energized the relay RL1 and switch-off the appliance.

PARTS LIST

Resistors (all ¼-watt, ~+mn~ 5% Carbon)

R1 = 147 Ω/2W

R2 = 100 Ω/1W

R3 = 330 Ω

R4 = 100 KΩ

R5 = 1.8 KΩ

R6, R7 = 1 KΩ

VR1 = 10 KΩ

VR2 = 22 KΩ
Capacitors

C1, C4, C5 = 0.01 µF

C2 = 1000 µF/25V

C3 = 100 µF/25V
Semiconductors

IC1 = µA741 (Operational Amplifier)

IC2 = 7812

T1= BC547

T2 = SL100

D1, D2, D3, D4, D5 = 1N4007

D6 = 1N4148

ZD1 = 5.1V zener diode
Miscellaneous

X1 = 230V AC primary to 7.5V-0-7.5V, 1A secondary transformer

RL1 = 12V, 200Ω 1 C/O Relay

LED1 = RED

Read More

Electronic siren circuit Diagram

Electronic siren circuit Diagram

WEARIFY   March 28, 2018   No comments:

This is a compact electronic siren circuit based on three transistors.This circuit is suitable for in corporating with other alarm or siren projects such as burglar alarms, automatic factory sirens etc or a simple push to on alarm.

The  electronic siren circuit given here  is  based on a complementary transistor pair consisting of Q2 & Q3 (BC557 & BC 37)  wired as an astable multivibrator oscillator,which directly drives the speaker.The transistor Q1 is used to provide a full charge on capacitor C2 when power is turned ON. When push button switch S1 is pressed , the capacitor C2 slowly discharges through resistor R8.This makes the circuit to  oscillate at a low frequency that increases to a high frequency and kept indefinitely as the capacitor is fully discharged. When the switch P1 is released, the output  frequency decreases slowly as C2 is charged to the  positive voltage through resistance R6 and the Base-Emitter junction of tramsistor Q2. When C2 is fully charged to the positive battery voltage the  circuit stops oscillating.

Electronic siren circuit Diagram with Parts list.

Notes.

• A 12 V battery or a a well regulated 12V DC power supply can be used to power the circuit.
• Assemble the circuit on a good quality PCB or common board.
• The switch S1 can be used to activate the alarm.
• The switch S2 can be used as a power switch.
• You can experiment on the tone of alarm by using different values for C2 and R8.

Link: Circuitslead

Read More

Dual Sensor 555 Timer Alarm

Dual Sensor 555 Timer Alarm

WEARIFY   March 09, 2018   No comments:

This electronic circuit is a very nice and simple alarm circuit that is based on the 555 timer integrated circuit. This alarm circuit can be used with many types of sensors like : light or temperature sensors. As you can see below some types of sensors that can be connected at this type of alarm circuit ( darkness , light , cold and heat sensor ).

If the sensor detects that the temperature or light is outside of the desired range the alarm will be activated .By turning the  potentiometer from the base of Q1  you will modify the sensibility of the sensor . When the alarm is activated the Q2 transistor acts as an audio amplifier and speaker driver for the 16 ohms speaker .

This alarm circuit require a 12 volts DC power supply circuit .

Read More

A Simple - Yet Useful Video Switcher

A Simple - Yet Useful Video Switcher

WEARIFY   March 06, 2018   No comments:

With the cost of security cameras going down, adding a surveillance system for your store, office or home is becoming more practical all the time. However, you might be dismayed at the thought of having to buy a monitor for every camera that’s installed. dedicating a single monitor to a single camera also runs the risk of burning the camera’s image into the phosphor screen of the CRT. If you prefer a single monitor instead of the “NASA-Mission Control” look, you could buy a special monitor that has a video switcher built in. That type of monitor can automatically switch between several camera inputs in sequence.

Yet Useful Video Switcher Circuit Diagram:

With that type of arrangement, you’d have to watch only one screen instead of having to scan a wall of CRTs. Switching between several cameras would also prevent image burn-in on the monitor. Those types of monitors, unfortunately, are also very expensive, offsetting the cost savings of even the cheapest surveillance camera. Video switchers are also available, but the cost of a switcher and a monitor could be as expensive as a monitor/switcher combination unit. A viable alternative for a video switcher is to build your own. Thanks to some recently introduced ICs, the cost and effort of designing and building such a unit has become both quite affordable and easy.


The video switcher described here can display the output of two, three, or four cameras on a single monitor. The number of cameras is set by a DIP switch on the circuit board. That feature avoids blank displays if less than four cameras are used by sequencing through only the inputs that are connected to a camera. In the automatic mode, the cameras are switched at a rate that can be varied with a panel mounted control. The switching rate can be set from about once per second to about once every 20 seconds. In the manual mode, one camera output is displayed continuously. A momentary-toggle switch is then used to step through the various cameras.

How it works

The heart of the video switcher is a Maxim MAX454. That integrated circuit contains a four-way video multiplexer and an amplifier that operates as a low-impedance line driver. The resulting video output is high quality with very low phase distortion. The video inputs are selected by applying a binary number to the address inputs. The binary number is also used to light a series of LEDs that indicate whichh camera input is currently selected. The circuit is powered by a 9-volt AC wall-adapter transformer, two diodes, and two voltage regulators.

Circuit description

Figure 1 is a schematic diagram of the video switcher. Multiplexer IC1 has four video inputs, two address inputs, one video output, one external amplifier input, and and three power terminals. The video cameras connect to the video inputs through J1-J4. The inputs are terminated with 75 ohm resistors R1-R4. The gain of the internal video amplifier is set by a feedback network connected to pin 13 of IC1. That feedback network consists of R5-R8 and C3. The gain is set to 2 in order to compensate for any loss through the 75 ohm terminator resistor, R9. The resulting net gain is 1 at output J5.

The binary addressing circuit is built around IC2, a CD4017 decade counter. That chip produces one positive output at a time on each of its ten outputs in sequence for every clock pulse. The first four outputs at pins 3,2,4,and 7 are connected to transistors Q1- Q4. Those transistors drive LED1-LED4 through current limiting resistor R15. The outputs from IC2 (pins 2,4, and 7) are also decoded into binary logic by diodes D1-D4. The binary logic is sent to the address input lines of IC1.


The number of cameras connected to the video switcher is set with S1. Each switch in S1 is connected to an output from IC2. If, for example, there are only two cameras connected to the video switcher, S1-a is closed. That connects the third output to IC2’s reset line. When IC2 advances to the third count, that output passes through S1-a to the reset, and IC2 resets to zero, activating the first camera. The sequence would be camera 1, camera 2, then back to camera 1. Closing S1-b or S1-c instead of S1-a will let the video switcher cycle through three or four cameras, respectively.

Clock pulses for the counter are generated by IC3, an LMC555 CMOS timer. The pulse rate and pulse width is controlled by C4, R10, R11 and potentiometer R12. By adjusting R12, the output frequency of IC3 can be controlled between 1 Hz and 1/20 Hz. The clock pulses from IC3 are connected to IC2 through S2, a three position toggle switch. Switching S2 to the auto position lets the pulses from IC3 select the next camera at a rate set by R12. When S2 is in its center-off position, no switching takes place, and whatever camera input is selected is passed through to the output.


The select position on S2 is a momentary contact. That position raises the clock input of IC2 to 5 volts, which increments the binary count and selects the next camera. When S2 is released, it springs back to its center-off position. The clock input of IC2 is then held at a low-logic level by R13. The MAX454 requires ±5 volts while the other ICs require only +5 volts. Power is supplied by AC adapter T1, rectifier diodes D5 and D6, regulators IC4 and IC5, and filter capacitors C6-C9.

Construction

Because of the high frequency video signals involved, the video switcher should be built on a printed circuit board. The circuit is simple enough to fit onto a single-sided board with only two jumpers needed. A foil pattern is included for etching and drilling your own board. Alternatively, an etched board can be purchased from the source given in the parts list. A feature of that board design is ground traces that run between all of the video signal traces in order to keep induced noise and crosstalk between the signals to a minimum.

Weather you etch a board from the foil pattern or purchase one from the source in the parts list, use the parts-placement diagram in fig. 2 for component placement. It is easiest to install and solder the resistors and diodes first. Once those components are in place, scrap component leads can be used for the two jumper wires. Next, install S1 and sockets for IC2 and IC3. Do not use a socket for IC1, the MAX454 multiplexer.

When installing J1-J5, hold the connectors tight against the board while soldering the center pin. The assembly can then be placed on a heat-resistant surface and the ground pins soldered. Because of their size and mass, a larger soldering iron might be needed to solder J1-J5. Otherwise the board might be damaged if heat is applied too long. Once the connectors are soldered in place, Q1-Q4, IC4, IC5, and all the capacitors can be installed. The LEDs should be installed next, leaving their leads long so that they can be bent to reach through the front panel of the enclosure.

Double-check the orientation of the polarized components, so that they are not installed backwards by accident. Once a component is soldered in place, removing it becomes much more difficult. Solder two 3-inch long wires onto the two terminals of R12 that are clockwise when viewing the potentiometer from the back. Connect those wires to the holes for R12 on the board. Three additional 3-inch long wires are soldered onto the terminals of S2. The center terminal connects to the hole near C5 and R13.

The momentary-contact terminal connects to the hole near R14. The remaining terminal connects to the hole near IC3 and R10. Solder IC1 directly onto the circuit board. That will result in the shortest possible lead length for the video signals. Plug IC2 and IC3 into their sockets, being careful to handle them as static-sensitive CMOS devices. Solder the T1 leads onto the board. Examine the board for any wiring errors, bad solder joints, and incorrect components. Once the assembly is inspected, it can be tested.

Testing

Plug T1 into an AC outlet and measure the voltages across C8 nd C9. The voltage across C8 should measure +5 volts. Across C9, the voltage should be -5 volts. To select two cameras, set S1-a on; to select three cameras, set set S1-b on; and to select all four cameras, set S1-c on. Only one switch at a time should be on. When switch S2 is toggled to its momentary position, the LEDs should sequence to the next indicator each time S2 is toggled. The order of the LEDs should cycle from 1 through 4 and repeat. When S2 is set to automatic, the LEDs should automatically at a rate that should vary as potentiometer R12 is adjusted. Connect cameras to J1-J4 and a monitor to J5.

The video signal on the monitor should switch from camera to camera according to the LEDs. After testing is completed, drill appropriate holes in a suitable enclosure for J1-J5, LED1-LED4, S2, and R12. Mount the board in the enclosure using the mounting hardware for J1-J5 to hold it in place. Mount R12 and S2 in the front panel and bend the LEDs so they fit through the holes in the panel. The hole for the T1 wire should be drilled at a point where the two halves of the enclosure meet.

Tie a knot in the wire for strain relief and place the wire in the enclosure hole with the knot on the inside of the enclosure before closing the case. That completes the project. If all has gone well, as is likely, your video switcher is now ready for use.

SEMICONDUCTORS
IC1 - MAX454 multiplexer, integrated circuit (MAXIM)
IC2 - CD4017 decade counter, integrated circuit
IC3 - LMC555 timer, integrated circuit
IC4 - 78l05 voltage regulator, integrated circuit
IC5 - 79l05 voltage regulator, integrated circuit
Q1-Q4 - MPSA14, NPN transistor
D1-D4 - 1N914, silicon diode
D5, D6 - 1N4004, silicon diode
LED1-LED4 - Light emitting diode, red

RESISTORS
R1-R4, R9-R15 - 75 ohm
R5 - 150,000 ohm
R6 - 620 ohm
R7 - 1100 ohm
R8 - 1000 ohm
R10 - 10,000 ohm
R11 - 51,000 ohm
R12 - I megohm potentiometer, panel mount
R13, R14 - 100,000 ohm

CAPACITORS
C1,C2,C5 - 0.1mF, 50WVDC, metalized film
C3 - 6.8 pF, ceramic disc
C4 - 10 mF, 50 WVDC, low leakage electrolytic
C5, C7 - 470 mF, 25 WVDC, electrolytic
C8, C9 - 100 mF, 16 WVDC, electrolytic

ADDITIONAL PARTS AND MATERIALS
S1 - DIP switch, 3 position
S2 - Toggle switch, single pole double throw, one momentary position
J1-J5 - Video connector, chassis mount, “F” type
T1 - 9 volt AC wall adapter transformer, PC board, IC sockets, LED holders, 22 gauge hookup wire, knob, enclosure, hardware, etc.

Read More

Simple Fog Lamp Sensor

Simple Fog Lamp Sensor

WEARIFY   March 06, 2018   No comments:

For several years now, a rear fog lamp has been mandatory for trailers and caravans in order to improve visibility under foggy conditions. When this fog lamp is switched on, the fog lamp of the pulling vehicle must be switched of to avoid irritating reflections. For this purpose, a mechanical switch is now built into the 13-way female connector in order to switch of the fog lamp of the pulling vehicle and switch on the fog lamp of the trailer or caravan. For anyone who uses a 7-way connector, this switching can also be implemented electronically with the aid of the circuit illustrated here.

Fog Lamp Sensor Circuit Diagram:

Here a type P521 optocoupler detects whether the fog lamp of the caravan or trailer is connected. If the fog lamp is switched on in the car, a current flows through the caravan fog lamp via diodes D1 and D2. This causes the LED in the optocoupler to light up, with the result that the photo-transistor conducts and energies the relay via transistor T1. The relay switches of the fog lamp of the car. For anyone who’s not all thumbs, this small circuit can easily be built on a small piece of perforated circuit board and then fitted somewhere close to the rear lamp fitting of the pulling vehicle. Link

Read More

Door Opening Alarm with Sound Alert

Door Opening Alarm with Sound Alert

WEARIFY   October 24, 2017   No comments:

The door opening alarm circuit or “Front Office Visitor Alert” is used for alerting you when a customer is at your office/shop. It will produce a beep sound when each new customer or visitor is entering, and will automatically switch OFF after few seconds.

Alarm with Sound Alert

In this circuit timer IC NE555 is used as monostable mode. Initially when the door is closed; reed switch (normally open type) near the magnet is closed. When the door is opened by someone, the reed switch near the magnet is open and the base of Transistor Q1 goes low through the 10k Resistor R2, and so Transistor Q1 is ON. At this time trigger pin 2 of the IC1 go low, it triggers the monostable built around IC NE555. Once triggered, output pin 3 of IC1 goes high, and both Buzzer and LED are turned on.

At this time the Capacitor C1 starts charging through the Transistor Q1. After few seconds the Buzzer and LED will automatically switched OFF. When the door is closed the T ransistor base become high, Transistor Q1 goes OFF and the Capacitor C1 starts discharging through the Resistor R4 is connected parallel with the capacitor C1. You can change the time period of IC1 by changing the values of resistor R5 and capacitor C2.

Assemble the circuit on a general-purpose PCB, enclose in a suitable cabinet and the magnet is fixed on the door frame and the reed switch is fixed on the door, near the magnet. The circuit can be powered from a 6V battery or from mains by using a 6V power adaptor.

Sourced By : w3circuits

Read More